Eibmarkt.com

manufacturer-number: NYM-J5x1,5Eca - Building wire 5x1,5mm² 300/500V Conductor material Copper, Nominal cross section conductor 1,5mm², Conductor category Class 1 = solid, Number of cores 5, Core insulation material Polyvinyl chloride (PVC), Core identification Colour, Max. conductor temperature 70°C, Protective conductor, Protective barrier None, Armouring/reinforcement None, Material outer sheath Polyvinyl chloride (PVC), Colour outer sheath Grey, Reaction-to-fire class according to EN 13501-6 Eca, Flame retardant In accordance with EN 60332-1-2, Insulation integrity No, Outer diameter approx. 10,8mm, Permitted cable outer temperature during assembling/handling 5 ... 70°C, Permitted cable outer temperature after assembling without vibration -40 ... 70°C, Nominal voltage U0 300V, Nominal voltage U 500V - NYM-J 5x 1,5 Eca

manufacturer-number: NYM-J3x1,5Eca - Building wire 3x1,5mm² 300/500V Conductor material Copper, Nominal cross section conductor 1,5mm², Conductor category Class 1 = solid, Number of cores 3, Core insulation material Polyvinyl chloride (PVC), Core identification Colour, Max. conductor temperature 70°C, Protective conductor, Protective barrier None, Armouring/reinforcement None, Material outer sheath Polyvinyl chloride (PVC), Colour outer sheath Grey, Reaction-to-fire class according to EN 13501-6 Eca, Flame retardant In accordance with EN 60332-1-2, Insulation integrity No, Outer diameter approx. 9,1mm, Permitted cable outer temperature during assembling/handling 5 ... 70°C, Permitted cable outer temperature after assembling without vibration -40 ... 70°C, Nominal voltage U0 300V, Nominal voltage U 500V - NYM-J 3x 1,5 Eca

manufacturer-number: JA.6.230 - KNX shutter/blind actuator 6fold 230V, DRA JA.6.230. Very high quality and unique price-/ performance relationship Our own direct distribution (directly ex works) enables us to provide extremely advantageous prices. Thus, you will be able to save more than 30% compared with similar high-quality products. The KNX blind-/shutter actuator JA.6.230 is a MDRC device to be mounted on a 35mm DIN-rail and to be installed into elctrical distributors. The actuator switches up to 6 electrical devices (motors 230V AC). Programmable from ETS 4 and higher. EIBMARKT® GmbH Holding (www.eibmarkt.de) presents a new 230V EIB/KNX shutter/blind actuator 6-fold (N000303) with manual operation (mounting method DRA, modular spacings 6). Special advantages are: Use of bistabile relays, only with this can a preferred state be set in case of bus failure, no additional power supply (KNX only), little space required and a very comprehensive ETS application. The actuator offers exten…

manufacturer-number: SA.12.16 - KNX Switch Actuator 12f. SA.12.16 - EIBMARKT GmbH 6f. 16A, 6f. 8A (230V AC1), Order number N000202. Requirement for programming: ETS 4 or higher. 12-fold switch with very large parameters. Application as Switch actuator (adjustable per channel) with preset, scene and threshold value function, per channel including two parmeterizable logic functions, one timer function (On/Off/Staircase) as well as positively driven operation and safety objects. Additionally, each channel can be parameterized as NCC or NOC with status feedback and operating hour counter. Application as Heating actuator (adjustable per channel) with regulator monitoring (failure control signal temperature sensor),can be parameterized with pulse width modulation via 1byte object (PWM) per channel, including rinsing function, positively driven operation function and status function and operating hour counter. Sample functions in switch actuator mode: Besides the many parameters, this actua…

EAN: 4250679710571 - manufacturer-number: HCAHNG-B2103-A010 - RJ45 8(8) Patch cord 1m - HCAHNG-B2103-A010

manufacturer-number: SV-2 - EIB KNX Power Supply SV-2 2500 mA / DC The output can be used as power supply for external devices - adjustable up to 29.5V, e.g. for binary inputs 24V DC or other devices (DC). In connection with a choke and a current limiter module each the power supply can be used to supply several EIB KNX lines (see SV-2/DR1 to DR4) Technical data: -Input: 85-264 VAC, 95-250 VDC (terminal 1=L, terminal 2=N) -Output: variable by means of potentiometer from 22.5 to 29.5 VDC -Preset: 24 VDC -Output current: max. 2500 mA -Ripple: max. 50 mV -Operating temperature: -25°C - +70°C -Protection: IP 20 -REG case for DIN rail, 4 TE - SV-2

manufacturer-number: N000401 - Note: The Power over Ethernet supply is standardized acc. to Standard PoE (IEEE 802.3af) and integrated via RJ45. We can recommend a PoE Ethernet Switch from Netgear, e.g. FS108P. The device disposes of 8 ports, four of which are equipped with Power over Ethernet (IEEE802.3af, 48 VDC). The IP interface, for example, can be connected to one of these four ports. As an alternative, power supply can be provided by means of screw connecting terminals at the upper side using a separate power supply unit (12-24V DC) or transformer (12-24V AC). Parallel power must be avoided! Caution when using managed Switches (Cisco or similar): With some Switches there can problems with the standard settings and the IP devices are not recognized. In this case make the following adjustment at the Switch: Full-Duplex-Mode Digit rate: 10 Megabit/s A blinking Ethernet LED at the IP Router or IP Interface indicates an existing link i.e. the digit rate and the mode have been set …

manufacturer-number: N000402 - Note: The Power over Ethernet supply is standardized acc. to Standard PoE (IEEE 802.3af) and integrated via RJ45. We can recommend a PoE Ethernet Switch from Netgear, e.g. FS108P. The device disposes of 8 ports, four of which are equipped with Power over Ethernet (IEEE802.3af, 48 VDC). The IP Router, for example, can be connected to one of these four ports. As an alternative, power supply can be provided by means of screw connecting terminals at the upper side using a separate power supply unit (12-24V DC) or transformer (12-24V AC). Parallel power must be avoided! Caution when using managed Switches (Cisco or similar): With some Switches there can problems with the standard settings and the IP devices are not recognized. In this case make the following adjustment at the Switch: Full-Duplex-Mode Digit rate: 10 Megabit/s A blinking Ethernet LED at the IP Router or IP Interface indicates an existing link i.e. the digit rate and the mode have been set cor…

EAN: 4260643463150 - manufacturer-number: KNX-40E-1280 - The Mean Well EIB/KNX power supply KNX-40E-1280 D is a 1280mA power supply with high efficiency and a small footprint of only 4SU (72mm). The device has a KNX bus choke output and an additional output for auxiliary power. The -30°,C to 70°,C wide temperature operating range can meet all kinds of applications. It is perfectly suitable to power up any products labeled with the KNX trademark. With over 30 years of industrial power supply experience, KNX-40E-1280 D is engineered to be a reliable and safe solution for the KNX bus environment.Features:EIB/KNX power supply with integrated chokeCompact size with 4SU width (72mm)Safety extra low voltage (SELV)Suitable for TP1-256180~264 VAC inputProtections: short circuit / overload(short-circuit-proof) / over voltageCooling by free air convectionIsolation class ILED indicator for normal operation, bus reset and bus overloadInstalled on DIN rail TS-35/7.5 or 15Over Voltage category III100…

EAN: 4021087049139 - manufacturer-number: KAA-4R4V-10 - The EIB/KNX Dimming actuator KAA-4R4V is a 4 channel device with high quality independent latching relays, suitable for all kinds of MeanWell LED drivers. There is, in addition, a DC 0(1)-10V signal output to perform the dimming on the connected drivers at each channel at the bottom terminal. The dimming curve can be adjusted to linear or logarithmic mode so as to provide an excellent dimming experience for the end users. It also can be used with motion sensors in buildings to save energy.The actuator is powered via the EIB/KNX bus and do not require any additional power supply. The EIB/KNX Dimming actuator KAA-4R4V is featuring both reliability and multi-functionality to meet various needs in a modern building.FeaturesEIB/KNX Dimming Actuator 4-foldDC 0(1)-10V dimmer 4-fold, 230V AC, 16A4 Channels for LED drivers, lighting switching outputs or for ohmic loads up to 3680W per channelany supposable mixed form of switching outputs a…